Hello friends! I am so excited to have you back and to share with you this fun, DIY Faux Wood Pallet Map Art. That’s right, it’s faux wood. You probably know it better by calling it, wait for it…. styrofoam. That’s right! This is such a cool project, and one I hope you take the time to try and recreate.
When I went to the SNAP! conference in Salt Lake City this past April, I met the wonderful ladies from FloraCraft® and fell in love with their large faux pallet map. Now, there pallet map was ginormous! Way too big for my little patio home, so I had to scale things down a bit for this version.
It also reminds me a lot of the Pallet Map Art that Pottery Barn retails for over $200! Well, this version is not only cost efficient, but it is super light! Let’s jump into how I made this map.
Here is what you are going to need to recreate this Faux Wood Pallet Map Art:
DIY Faux Wood Pallet Map Art
- (2) 1 x 12 x 36 piece of Make It Fun® FloraCraft® Styrofoam
- FloraCraft® Foam Connectors & Eyelets
- Make It Fun® FloraCraft® Smooth Finish
- creme wax color (I used Americana Decor® in deep brown)
- map stencil (I cute mine out from my Silhouette with vinyl)
- white spray paint
- light (120 grit) sand paper
The first thing I did was take my ruler and pen and mark my foam sheets every 4 inches.
After you have marked the foam, take the StyroCutter® and cut along your lines as best as you can.
After the foam is cut, take your pieces and grab the FloraCraft® SmoothFinish® and a spatula to create your faux wood look. Just apply a really smooth stroke and make sure to cover all of the foam. Just take your time, it goes on really easy.
After you have done all of your boards and allowed them to dry completely (I opted to only do 5 because I wanted my faux pallet to be a bit smaller than it would have been with all 6) it’s time to add the wood color.
The first thing I did was take my sandpaper and lightly sand any really rough spots on the smooth finish. There were not many, so that was a quick fix! I then grabbed a foam brush applicator and the creme wax color and applied it carefully and smoothly over all of the foam top. After I did my first coat, I went back and added a little more to a few spots to make it look a little more realistic.
Once the color was dry, it was time to secure the foam boards together to create my pallet look. I grabbed my FloraCraft® Foam Connectors and Eyelets and spaced them every 9 inches on one side of the boards, which is 4 connectors to each board.
After the boards were connected, I also added a couple of strips of clear tape to make sure everything stays together. Now I am ready to stencil!
I then created a stencil on my Silhouette machine and sliced it into three halves so I could make it large enough for me faux pallet. You can find the tutorial on how to do that here.
After I created my stencil, I applied it to my board and then applied a cover over any extra exposed areas of my faux pallet.
Once I had all of my areas covered, I gave them a nice coat of white spray paint, staying a good 15-20 inches above the board and covering it in a sweeping motion. After I was confident I had the entire area covered, I removed the stencil before it was completely dry. I did this for two reasons: I didn’t want the paint to possibly pull up in spots with the stencil if I let it fully dry, and I also didn’t want to leave the sticky vinyl on the SmoothFinish and possibly remove some of it and possibly expose foam. So in a matter of minutes, I was finished!
What do you think? Looks a lot like a scruffy wood pallet to me! Here is a close up.
It is so light, I bet this project weighs less than 2 pounds! Much easier to hang up and move than an actual wooden pallet. Not to mention, you don’t have to worry about termites! Ha!
I hope you enjoyed this DIY Faux Wood Pallet Map Art and if you are ready to tackle a cool project, you should give this fun idea a try!
Thank you again to the people at FloraCraft® for making this project possible!