I finally turned the toddlers bed into her “big girl” bed a few months ago. Ever since I have been wanting to do something special for her room. I have always loved bed cornices, but they are just so expensive. This (of course) had me thinking I could do it myself, so I did! I created this Easy DIY Bed Crown Cornice for under $50. That includes everything, including the panels, which can be EXPENSIVE.
I have found these Bed Crown Cornice pieces from $50 – 200 and up, I mean WAY up. If you have searched for these like I have, you know what I am talking about. It can be costly. Needless to say, I have had a ton of fun with my power tools creating this one. I also did this all by myself, so no worries on wondering if you can do this.
I hope you give this project a try, it was surprisingly easy, and a beautiful project in the end. Just make sure to read through all of the steps before you get started. I am going to split this up into a couple of posts. This one telling you how to create the bed crown cornice, and a second one showing you how to cover the cornice and make it pretty!! You will find a few affiliate links below for some of the products I used in creating this cornice. Let’s get started.
Easy DIY Bed Crown Cornice Tutorial
- template (I created one in my Silhouette Cameo for the base structure)
- 1″ 2′ x 2′ plywood (cut your semicircles and base from this piece)
- 1/4″ soft plywood (for the curved top of the base)
- 1 x 3 x 8 cut into
- 1 x 4 x 8 cut into
- Dry Dex Spackling & Nail Hole filler (optional if covering with fabric)
- primer (optional if covering with fabric)
- cut 2 24″ long 5″ tall semi circle pieces from 1″ x 2 x 2(using template below)
- cut 1 24″ x 5″ piece from 1″x 2 x 2
- cut 1/4″ 28″ x 17″ for the curved top piece
- cut 1 x 3 x 8 into (3) 5″ pieces (braces)
- cut 1 x 4 x 8 into (2) 8″ pieces and (1) 22″ piece
How I made the bed crown cornice template
I used Silhouette Designer Software to create a template. To do this, create an oblong circle that is 24″ long and 10″ in width, and then place a cut line down the middle.
Once the pieces have been cut from vinyl, attach the vinyl sheets to the 2 x 2 plywood piece.
Once you have the vinyl set, take your jigsaw and adjust the setting for the correct cut and depth and then cut out your pieces.
You should have a semi circle that looks like this.
Do this again until you have both pieces cut out. Make sure to hand sand any rough edges you may have on the boards.
Take the 1/4 plywood piece that is 24″ x 5″ and attach the two semi circle pieces.
Attach the (3) 5″ braces in between your semi circles.
How did I put all of this together? I attached these all very seamlessly and easily using my Ryobi Airstrike Brad nailer. This tool allowed be to attach these pieces and make it one solid piece in less than 5 minutes! If you don’t have one, borrow one. You will love life!
It was time to attach the curved top portion. Here is where I made a mistake. I cut my top piece at 24″. It should have been longer because the curve will take away some of the length. Make sure you do a better job of measuring your top piece. I would suggest 28″ versus 24″. This should be 28″ by 17″.
After this is cut, it is time to attach this to the curved base. Center the top piece onto your base you just built. Using your drill, place two screws attaching the top to the base.
Once you have this piece attached, use your clamps to slowly bend the board down on one end. about halfway down, place two more screws into the base frame. Then attach two more screws close to the bottom of the frame. Then do these same steps on the other side. (You can see I made a couple of booboos.)
I took wood filler and primer and finished up the top. I am covering this piece, but I still wanted to make it a little better.
After I finished with this (now) full cornice piece, I attached the braces that will attach to the wall when it is hanging.
The final piece looks like this before adding all of the pretty stuff…
Whew! That was fun! I also have a cut board that is attached to the bedroom wall that is centered to the bed and attached to a couple of studs so it will be safe and sturdy.
Make sure to stick around and I will show you later this week how I covered the cornice. What do you think? Do you feel like you can make one of these now?
This was such a fun project, so stick around for the second half of this Easy DIY Bed Crown Cornice where I show you how to cover it and make it pretty!